LVDEPLOY — LOW VOLTAGE DEPLOY

Smart Digital Tech — LVDeploy v1.0 — Authorised Personnel Only

⚠ Disclaimer & Acceptable Use This tool is the exclusive property of Smart Digital Tech and is intended solely for authorised personnel. All data entered is for internal cabling documentation purposes only. Unauthorised access, distribution, or reproduction of this tool or its contents is strictly prohibited. By logging in you agree to use this tool responsibly and in accordance with Smart Digital Tech policies. Smart Digital Tech accepts no liability for inaccurate documentation entered by users.

Username

Password

Incorrect username or password. Please try again.

Low Voltage Deployment Tool

Upload a floor plan, place data port locations, draw cable runs to MDF/IDF, Instantly generate a Bill of Materials, install time estimates and a project task list.

Termination rooms

MDFMDF room

IDFIDF closet

PData Ports

▼

11-port outlet

22-port outlet

33-port outlet

44-port outlet

55-port outlet

66-port outlet

IPWireless & IP Devices

▼

WAPWireless Access Point

CAMIP Camera (PoE)

VoIPVoIP Phone

IoTIoT / Smart Device

TVTV / Monitor (Network)

⚡ PoE Note: WAP/CAM/VoIP require PoE switch ports. Cat6A recommended for PoE++ loads.

ACAccess Control

▼

DOORDoor Location

ACPAC Controller / Panel

AC cabling type

🔒 Tip: Drag door & panel onto the floor plan, then right-click a door to connect it to its controller panel.

AUAudio Cabling

▼

SPKCeiling Speaker (70V/8Ω)

WSKWall Speaker / Horn

SUBSubwoofer / Floor Speaker

VOLVolume Control / Attenuator

AMPAmplifier / Zone Controller

WPLAudio Wall Plate (RCA/XLR)

🔊 Audio Note: Speakers use 16/2 (or 14/2 for subs). 70V systems require transformer tap setting at each speaker.

FFiber Runs

▼

OM3OM3 — 6 strand

OM3OM3 — 12 strand

OM3OM3 — 18 strand

OM4OM4 — 6 strand

OM4OM4 — 12 strand

OM4OM4 — 18 strand

SMSingle Mode — 6 strand

SMSingle Mode — 12 strand

SMSingle Mode — 18 strand

📝Canvas Notes

▼

📝Note / Annotation

Drag onto canvas, then double-click to edit. Use Draw Cables to draw a pointer arrow to any node.

Device cable type

Data cable type

Cable jacket type

Data cabling testing & certification

Fiber testing

Floor plan scale

px = ft

Cable path & wall height

Ceiling ht ft

Port ht (off floor) ft

MDF patch ht ft (rack)

Add 15% cable slack

Service loop ft per run

Added to every cable run for termination slack at both ends.

Rack / enclosure size

Rack size

PoE switch size

UPS / PDU

Auto-save

Auto-save every min

Not saved yet

Room dimensions

Lengthft

Widthft

Ceiling htft

MDF wall

MDF offsetft

Slack

Port locations

Enter dimensions and click Calculate

💼 Project

👤 Customer

📅 Date

📄 PO #

👷 Crew Lead

Upload a floor plan or drag ports onto the canvas

Best floor plan size: 1200 × 700px PNG | Also supports JPG, GIF, PDF, XLS, XLSX

Use ⊸ Sidebar in the toolbar to hide the left panel for maximum width

Bill of materials

Cable schedule

Install time

🗄 Rack Calc

☑ Install List

Place ports on the canvas and click Generate BOM

Ready — drag ports from the left panel onto the canvas

Cable Type	Jacket	1000ft Box Cost ($)	Per-Foot Cost ($/ft)
Cat5e	Riser CMR	$	$
Cat5e	Plenum CMP	$	$
Cat6	Riser CMR	$	$
Cat6	Plenum CMP	$	$
Cat6A	Riser CMR	$	$
Cat6A	Plenum CMP	$	$
Cat7	Riser CMR	$	$
Cat7	Plenum CMP	$	$

LVDEPLOY — LOW VOLTAGE DEPLOY

Low Voltage Deployment Tool

📐 Generate Blank Floor Plan Template

Select Port / Box Type

Connection Type

📏 Set EMT Pipe Height

📝 Node Notes

⏱ Session Paused

Session Expiring